A 1.5 inch stainless welded mesh panel has square or rectangular openings made by welding stainless steel wires at their intersections. Before ordering, confirm whether “1.5 inch” means the clear opening or the wire-to-wire pitch: these measurements are not interchangeable. A 1.5 inch opening equals 38.1 mm, but the finished panel’s usable open area also depends on wire diameter. To select the right panel, specify the opening measurement, wire diameter, stainless steel grade, panel dimensions, finish, tolerances, and project environment.
This guide is for procurement teams, fabricators, contractors, and equipment manufacturers comparing mesh panel options. It explains what to request in a quotation, how to match specifications to an application, and which commercial details to confirm before placing an order. Shunqiang Wire Mesh can discuss project requirements with buyers seeking stainless welded mesh panels; final availability and specifications should be confirmed against the inquiry.
A welded mesh panel is made from intersecting wires joined at their crossing points, commonly by resistance welding. In a stainless version, the wires are made from stainless steel selected for the intended service conditions. The welded intersections create a fixed grid, while the panel can be supplied in a size and edge configuration agreed between buyer and supplier.
The term “1.5 inch mesh” can describe different dimensions in supplier quotations. It may refer to the clear distance between adjacent wires, or to the spacing measured from the center of one wire to the center of the next. Ask the supplier to state the measurement method on the drawing or quotation, particularly when the panel must fit a frame or work with other components.
Record the opening in both the preferred unit and a clearly stated measurement convention. If your drawing specifies a 1.5 inch clear opening, write “38.1 mm clear opening,” then identify the wire diameter as a separate specification. If the requirement instead describes pitch, state that explicitly and request a drawing showing how it is measured.
Wire diameter affects panel weight, stiffness, open area, and compatibility with the application. A thicker wire does not automatically make a panel suitable for every load or impact condition; support spacing and the way the panel is installed also matter. For a design that carries loads or protects people or machinery, have the responsible engineer verify the complete assembly rather than relying on mesh dimensions alone.
Common grades buyers may encounter include 304 and 316 stainless steel. Grade selection should reflect the chemicals, moisture, temperature, cleaning methods, and outdoor or indoor exposure expected at the site. Grade names alone do not establish suitability for a particular chemical environment, so provide the supplier with relevant operating conditions and confirm the proposed material before purchase.
Also clarify whether the quoted grade applies to the wire and whether material documentation is required. If the project has a material standard, drawing, or purchasing specification, share it with the supplier for review. Do not assume that a general description such as “stainless steel” satisfies a project’s traceability or compliance requirements.
Give the required panel width and length, along with any limits on flatness, squareness, or dimensional variation. As an illustrative quoting example only, a buyer might request a panel measuring 1000 × 2000 mm; this is not a standard size or a confirmed Shunqiang product dimension. If the panel must fit a frame, provide the frame’s internal dimensions and the clearance needed for installation.
Describe the panel edges needed for handling and assembly, such as whether wires should end flush with the boundary or extend beyond it. State any requirements for surface condition, cleaning, or protection during transport. If the panel will be cut or welded after delivery, discuss how the finishing and maintenance plan applies to the exposed areas.
With competitive price and timely delivery, Shunqiang Wire Mesh sincerely hope to be your supplier and partner.
A 1.5 inch opening may be considered for screening, separation, guarding, or fabrication, but suitability depends on the object being contained, the required visibility, and the loading conditions. A larger opening generally allows more passage through the grid than a smaller one, while wire diameter and framing influence the finished panel’s usable open area. Compare the mesh against the actual job requirement rather than selecting by opening size alone.
For a machine guard or safety barrier, check applicable site rules and conduct a risk assessment; mesh selection by itself does not establish compliance. For filtration or fine separation, confirm whether a 1.5 inch opening is sufficiently small for the target material. For outdoor or wet service, evaluate the stainless grade and maintenance conditions before approving the specification.
Write down what the panel must do: contain, separate, protect, support, or provide a visible barrier. Identify the smallest item that must be retained and any load, impact, or access requirements. This first step helps determine whether the proposed opening is appropriate or whether a different mesh design should be considered.
Prepare a short specification with the opening measurement method, wire diameter, grade, panel dimensions, edge details, finish, quantity, and tolerances. Include drawings or photographs when the panel connects to an existing frame or machine. If a dimension is flexible, mark it as a target or allowable range rather than leaving the supplier to infer your intent.
Check that the quotation repeats your key specifications and identifies any deviations or assumptions. Ask how the supplier will confirm dimensions and material grade, and whether inspection documents or a pre-production sample are available for your order. A sample or drawing review can help reveal misunderstandings before production, but its availability and scope should be agreed in advance.
Price, minimum order quantity, and lead time may depend on grade, wire diameter, panel size, quantity, fabrication steps, and destination. Request these terms in writing, including packaging, shipping basis, and any charges for cutting or special finishing. Do not compare quotations on unit price alone if their material, tolerances, or included services differ.
When evaluating a supplier, check whether its team can review drawings, clarify measurement conventions, and respond to material and fabrication questions. Ask for a quotation that clearly lists the grade, opening, wire diameter, panel dimensions, quantity, and agreed tolerances. If your procurement process requires material records, inspection information, or export documentation, state those requirements before ordering and confirm what can be provided.
Shunqiang Wire Mesh works with B2B buyers sourcing wire mesh products and can review the project details shared in an inquiry. To make the discussion efficient, provide the intended application, operating environment, drawings, required quantity, destination, and target delivery schedule. We can then assess the requested panel specification and clarify which details need confirmation before a quotation is finalized.
A 1.5 inch stainless welded mesh panel can be assessed for a project only when its opening convention, wire diameter, material grade, dimensions, and installation requirements are clearly defined. Treat 38.1 mm as the conversion for a 1.5 inch measurement, not as confirmation that every supplier uses the same opening convention. The right specification depends on the function and exposure conditions, and a mesh panel should not be treated as a complete safety or structural design without appropriate review.
As a next step, send Shunqiang Wire Mesh your drawing or a written specification, together with the application, quantity, destination, and any documentation requirements. Ask for a quotation that states the measurement method, material, tolerances, packaging, minimum order quantity, and lead time. Comparing suppliers against the same written requirements will help you evaluate fit, cost, and sourcing risk more reliably.
Contact us to discuss your requirements of 1.5 inch stainless welded mesh panel. Our experienced sales team can help you identify the options that best suit your needs.